设为首页|加入收藏

• 首 页
• 美军标 MIL
• 国际标准
• 协会标准
• 国内标准
• 论 坛

DIN EN 733-1995 带轴承座和PN10轴向端口的离心泵.额定功率.主要尺寸、标识系统;德文版本EN733:1995

上一篇: DIN EN 734-1995 带侧通道泵PN40.额定功率、主要尺寸、命名制度
下一篇: DIN EN 292-2-1995 机器的安全性.基本概念、一般设计原则.第2部分:技术原则和规范;德文版本EN292-2:1991+A1:1995

Product Code:SAE J356
Title:Welded Flash-Controlled Low-Carbon Steel Tubing Normalized for Bending, Double Flaring, and Beading *HS-150/2000*
Issuing Committee:Metallic Tubing Committee
Scope: The SAE Standard covers normalized electric-resistance welded flash-controlled single-wall, low-carbon steel pressure tubing intended for use as pressure lines and in other applications requiring tubing of a quality suitable for bending, double flaring, beading, forming, and brazing. Material produced to this specification is not intended to be used for single flare applications due to the potential leak path that would be caused by the ID weld bead.This specification also covers SAE J356 Type-A tubing. The mechanical properties and performance requirements of standard SAE J356 and SAE J356 Type-A are the same. Therefore, the designated differences of Type-A tubing are not meant to imply that Type-A tubing is in anyway inferior to standard SAE J356. The Type-A designation is only meant to address the unique manufacturing differences of the small diameter, light wall sizes (typically 15.88 mm OD x 1.24 mm wall and smaller.) The primary differences between SAE J356 and SAE J356 Type-A are described in the following paragraph.Type-A tubing is heat treated in-line to relieve stresses and is generally produced in coiled form. When Type-A tubing is produced in coil form, straight lengths of Type-A are only available through a secondary straightening and cut-to-length operation. Standard SAE J356 is produced as straight lengths and then receives a secondary normalizing operation. All standard SAE J356 requirements apply to Type-A tubing unless the specific requirement is noted with a 脪Type-A脫 designation. Standard SAE J356 is also available in the same sizes as Type-A, in which case all the standard SAE J356 specifications apply.
Rationale: The SAE Standard covers normalized electric-resistance welded flash-controlled single-wall, low-carbon steel pressure tubing intended for use as pressure lines and in other applications requiring tubing of a quality suitable for bending, double flaring, beading, forming, and brazing. Material produced to this specification is not intended to be used for single flare applications due to the potential leak path that would be caused by the ID weld bead.This specification also covers SAE J356 Type-A tubing. The mechanical properties and performance requirements of standard SAE J356 and SAE J356 Type-A are the same. Therefore, the designated differences of Type-A tubing are not meant to imply that Type-A tubing is in anyway inferior to standard SAE J356. The Type-A designation is only meant to address the unique manufacturing differences of the small diameter, light wall sizes (typically 15.88 mm OD x 1.24 mm wall and smaller.) The primary differences between SAE J356 and SAE J356 Type-A are described in the following paragraph.Type-A tubing is heat treated in-line to relieve stresses and is generally produced in coiled form. When Type-A tubing is produced in coil form, straight lengths of Type-A are only available through a secondary straightening and cut-to-length operation. Standard SAE J356 is produced as straight lengths and then receives a secondary normalizing operation. All standard SAE J356 requirements apply to Type-A tubing unless the specific requirement is noted with a 脪Type-A脫 designation. Standard SAE J356 is also available in the same sizes as Type-A, in which case all the standard SAE J356 specifications apply.

标准名称：	建筑变形测量规程JGJ/T8-97
中标分类：	工程建设 >> 工程勘察与岩土工程 >> 工程地址、水文地质勘察与岩土工程
ICS分类：
替代情况：	被JGJ 8-2007代替
发布日期：	1997-11-14
实施日期：	1998-06-01
首发日期：	1900-01-01
作废日期：	2008-03-01
出版社：	中国建筑工业出版社
出版日期：	2005-03-09
页数：	63页
书号：	15112.8760

没有内容

没有内容

没有内容

没有内容

© 2009-2024 标准资料网 版权所有，并保留所有权利。

北京智聚科技有限公司 Tel: 010-67123753 E-mail: kefu@infoeach.com

京ICP备14017250号-1